Troy bilt rototiller manual pdf

Mantis Tiller Manuals. Maxim Tiller Manuals. McCulloch Tiller Manuals. Montgomery Ward Tiller Manuals. MTD Tiller Manuals. Murray Tiller Manuals. New Holland Tiller Manuals. Poulan Tiller Manuals. Powermate Tiller Manuals. RedMax Tiller Manuals. Remington Tiller Manuals. Remington Power Tools Tiller Manuals. Ryobi Tiller Manuals. Call physician immediately. Keep out of reach of children. Ventilate when charging or using in an enclosed space. Always shield eyes when working near batteries.

If you have lost control of the tiller, and cannot reach the levers, LET GO of the handlebars and all controls and do not attempt to restrain the tiller.

The Forward Interlock Safety System will stop the engine. Store gasoline in a cool, wellventilated area, safely away from any spark or flame-producing equipment. Store gasoline in an approved container, safely out of the reach of children. Refer to the Maintenance and Service Section of this Manual if the tiller is to be stored for an extended period. When loading or unloading unit, always disengage the tines and use slower wheel and engine throttle speeds. See Section 3 in this Manual for the testing procedure to follow.

Revolving tines could be dangerous on slippery sidewalks or driveways. Contact us immediately for replacement decals if any are missing, illegible, or damaged. See your Parts Catalog for the exact location and part number of each decal. This lever engages power from the engine to the transmission see Photos , , and The transmission then. If the tines are removed and replaced with a PTO driven attachment, the lever will apply power to the attachment.

This is a safety feature for your protection. Practice shifting the lever as described next. For forward motion of the wheels and tines or to apply power to any PTO driven attachment , push the iever all the way down and release it.

See Photo The clutch roller lower photo will be engaged below the adjustment block. The clutch roller lower photo will rest anywhere on the face of the adjustment block, depending upon drive belt length and tension.

Then raise the tines out of the soil by lifting up on the handlebars, and slowly lift the lever all the. This is a good rule to follow. There are two Forward Interlock Levers, one located directly below each handlebar grip. Let go of lever to stop reverse motion. Continue to squeeze one or both of the interlock levers during all forward operation. To stop forward motion in an emergency, release BOTH interlock levers. This will cause the engine to shut off, stopping all forward motion.

If there is, the machine is badly out of adjustment and it should not be operated until the condition is corrected. When the clutch goes into gear, you will no longer be able to roll the wheels. If there is, shift the lever a little more either up or down to eliminate the noise—and the rubbing of the clutch and gear that causes it.

When the lever is in gear, you will no longer be able to roll the wheels. This will prevent damage to the clutch or wheel speed gears. This lever is located on the left side of the transmission, just forward of the tiller tine hood. You should also disengage the lever before towing or transporting any attachment. Doing so will help prevent damage to the transmission that could occur if you try to engage or disengage the separate drive shaft clutches while they are turning under power.

NOTE: The lever should move easily. This lever is located at the rear of the tine hood—see Photo It is used to regulate the tilling depth of the tines. In this position the tines will clear the ground by approximately 2 -inches, allowing you to transport the tiller without the tines—which should be disengaged—scraping your lawn or driveway.

These positions will allow the tines to dig just a few inches into the soil. The remaining notches are used for deeper tilling up to 8 -inches deep, depending on the soil conditions , and for turning under organic matter. This prevents the tines from touching the ground until you are ready to begin tilling.

This lever is located near the bottom of the handlebars, on the right side of the tiller. Support the handlebars with one hand while unwinding the lever enough so that the teeth in the ratchets are disengaged. Two additional height settings can be obtained by switching the inside handlebar ratchets, as shown in Figure This will change the handlebar height a few inches higher or lower than the lowest setting obtained in Step C.

Doing so could result in unsafe handling and personal injury. Please read that literature carefully and save it for future reference. This lever is located on the right side handlebar see Photo It is used to regulate engine speeds. In general, faster engine speeds will be required when breaking new ground or tilling under heavy crop residues, but remember to use only as fast an engine speed as is needed to do the job.

Try to judge when the engine is providing the proper amount of power—not too little, but not too much. The sound of the engine running will be your best guide. If adjustments are needed, refer to Section 6 of this Manual. Your erigine is equipped with a manually operated choke control as shown in Photo or The use of the choke for starting will vary, depending on air temperature and altitude.

Failure to do so can quickly build up carbon deposits that can harm the engine. The recoil starter is located at the front of the engine, as shown in Photo or On the 8 HP Kohler Engine, move the lever all the way up. When restarting an already warm engine, you may not have to use the choke at all. Then pull the handle with a rapid, continuous, full-arm stroke. Let the starter rope rewind slowly after each start attempt. To help avoid personal injury, be sure that the area behind you is clear before pulling the starter rope.

The key switch starter for the optional electric start engine is located on the right side of the battery hold-down clamp, as shown in Photo If the battery will not be used for oxlondcd periods of time, it should be fully charged before placing it in storage. Fuel Tank Shut-Off Valve. Your engine is equipped with a fuel tank shut-off valve. It is located underneath the gasoline tank.

See Photo or To operate the Key Switch Starter: A. Prolonged cranking can damage the starter motor if it is cranked more than 15 seconds per minute. This will cause. To avoid injury due to accidental or unauthorized engine starting, always remove the key from the switch when leaving the machine unattended. You should practice with your tiller in an open, level area before you use it in your garden.

Thereafter, change the oil after each 10 operating hours. The gear oil levels must be checked after the first 2 hours. Thereafter, check the oil levels after every 30 operating hours. The tension on the drive belt may need to be adjusted after the first 2 or 3 hours of new operation due to initial belt wear and seating of the belt with its pulleys.

For your safety, follow all steps and the cable. Tires Make sure that this is the cable on the left side, with one end attached to the solenoid. See Fig For shipping purposes, the tires may be overinflated. Be familiar with all the controls and power to the transmission. NOTE: Do not attempt to engage the tines, wheels, or any PTO attachment until you have read all of the operating instructions in this section.

Before attempting to do so, perform the with forward rotating tines. Page 16 When the tiller moves forward, relax and let the wheels Lift up the handlebars until the tines are off the ground, power the tiller along while the tines dig. Page 18 Changing Belt From Low Range to High Range Working from the left side of the tiller, work the belt as much as possible onto the top-front engine pulley groove. To avoid personal injury, shut off the engine, let all moving See Fig. Page 19 Clearing the Tines Stand on the left side of the tiller.

Use your left hand to move the belt off the most tangling of debris. As in terrace gardening, start composted. Pushing over but not uprooting at the top of the slope and overlap the first pass by half the cornstalks will often make it easier for your tiller to chop width of the tiller.

Page 23 Tilling Under Corn Removing the Tine Attachment After corn is harvested, the stalks should be tilled into the soil Move the tiller to level ground.

Dry plants are more difficult to till under, and Be sure the engine is stopped, the electric start key is the roots break loose too easily. Page 24 Then move the swing-out bolts out. The guide pin on the power unit will slide out of the guide hole in the tine attachment See Fig. O perat i on. Clutch 2 0. M a neu v ering Cl utch De pth Re gul ator Engin e C o nt rols St art in g Your Engi n e St art ing the Ele ct ri c Start Eng in e.

Turn ing Ar o u nd Sto pping t he Tiller and En gi ne Guid ing Your Tiller.